← Back to Caravan & Motorhome Troubleshooting

Bailey • Orion • 430-4 • 2012

372225 FAQs6 Types

Official manual on Bailey's site:View PDF ↗

Chassis & Running Gear Cooking & Kitchen Smoke & CO Alarms Toilets & Sanitation TV & Entertainment Water & Plumbing

Bailey

AL-KO AKS Stabiliser, Chassis & Braking System (2012 Model Year, Orion)

Chassis / Towing Control

61901 FAQ

View official manual on manufacturer's site ↗

Master Troubleshooting & Diagnostics Matrix

Error Code / Indicator	Symptom / Meaning	Possible Cause	Step-by-Step DIY Fix	Suggested Actions
`N/A`	Braking is one-sided	Incorrect adjustment at wheel	Adjust as described.	DIY Check / Tech Fallback
`N/A`	Braking is one-sided	Brake cable seized	Free off cable or replace.	DIY Check / Tech Fallback
`N/A`	Braking is one-sided	Brake lining contaminated with grease	Replace brake shoe assemblies.	DIY Check / Tech Fallback
`N/A`	Trailer brakes engage even under gentle deceleration	Overrun device's shock absorber has weakened or stopped working	Examine and replace if necessary.	DIY Check / Tech Fallback
`N/A`	Trailer brakes engage even under gentle deceleration	Brakes overadjusted	Re-adjust as described.	DIY Check / Tech Fallback
`N/A`	Brakes grab or snatch suddenly when applied	Brakes overadjusted	Re-adjust as described.	DIY Check / Tech Fallback
`N/A`	Brakes grab or snatch suddenly when applied	Brake cable sticking	Inspect the cable, working it loose or fitting a new one.	DIY Safe
`N/A`	Brakes grab or snatch suddenly when applied	Brakes under adjusted	Go over the whole brake transmission linkage and re-adjust as needed.	DIY Check / Tech Fallback
`N/A`	Brakes grab or snatch suddenly when applied	Shock absorber weak or ineffective	Replace.	DIY Check / Tech Fallback
`N/A`	Brakes grab or snatch suddenly when applied	Drawshaft sticking	Run it through its entire stroke, adding lubricant if needed.	DIY Safe
`N/A`	Brake judder	Linings contaminated with grease	Replace brake shoe assemblies.	DIY Check / Tech Fallback
`N/A`	Brake judder	The lining has separated (de-bonded) from its shoe	Replace brake shoe assembly.	DIY Check / Tech Fallback
`N/A`	Brake judder	Distorted/cracked drum	Replace.	DIY Check / Tech Fallback
`N/A`	Brake judder	Rust spots have formed on the drums' braking face	Sand the affected area smooth, then wipe it down with methylated spirit.	DIY Safe
`N/A`	Brakes seize up while reversing the trailer	Brakes overadjusted	Re-adjust as described.	DIY Check / Tech Fallback
`N/A`	Brakes seize up while reversing the trailer	Reverse lever not functioning	Check action and rectify.	DIY Safe
`N/A`	Brakes seize up while reversing the trailer	The ground itself is too soft or slick to grip	Lay matting (or something similarly firm) over the ground right there.	DIY Safe
`N/A`	Trailer brakes inoperative	Brakes underadjusted	Check action and rectify.	DIY Safe
`N/A`	Trailer brakes inoperative	Lining contamination	Replace brake shoe assemblies.	DIY Check / Tech Fallback
`N/A`	Trailer brakes inoperative	Seized cables	Free off or replace.	DIY Check / Tech Fallback
`N/A`	Trailer brakes inoperative	Linings worn out	Replace brake shoe assemblies.	DIY Check / Tech Fallback
`N/A`	Hot brakes	Brakes overadjusted	Re-adjust as described.	DIY Check / Tech Fallback
`N/A`	Hot brakes	Pull-off spring broken	Replace spring.	DIY Check / Tech Fallback
`N/A`	Hot brakes	Seized cables	Free off or replace.	DIY Check / Tech Fallback
`N/A`	Parking brake fails to hold the trailer on a gradient	Incorrect adjustment at spring cylinder	Re-adjust as described.	DIY Check / Tech Fallback

Frequently Asked Questions

Q: How do I fit the AL-KO Secure wheel lock to my caravan?ⓘ

First, line the wheel up so you can see the receiver through the centre of the rim - never use the opening where the tyre valve sits. Unwind the plastic cap covering the receiver and pop it in your toolkit for safekeeping (put it straight back on whenever the lock isn't fitted). Slot the locking bolt into its rim-specific insert, then fit the socket key onto it, and bring the whole locking-bolt assembly up level with the receiver.

Using the wheel spanner supplied (a torque wrench works too), tighten the locking bolt socket down to the correct wheel torque - around 86 Nm - then take the socket key back off. Finally, push the barrel lock into place, and hold everything firm while you turn the key to lock it - at that point the AL-KO Secure is properly fitted.

Note this was an optional-extra fitting on some editions, so check whether your caravan actually has it before following these steps.

Daewoo

Microwave Oven (as fitted to Bailey caravans, 2010-2019)

Microwave

1104 FAQs

View full Daewoo page →

Technical Specifications

Power Supply220V-240V 50Hz, Single Phase with Earthing

Microwave Power Consumption1200W

Microwave Output Power700W

Microwave Frequency2450MHz

Master Troubleshooting & Diagnostics Matrix

Error Code / Indicator	Symptom / Meaning	Possible Cause	Step-by-Step DIY Fix	Suggested Actions
`N/A`	The microwave oven doesn't work	Not connected to mains, door not firmly closed, cooking time not set, or a blown fuse/tripped circuit breaker.	Make sure the power cord is plugged in securely, the door is shut firmly, and a cooking time has actually been set. Also check for a blown fuse or a tripped circuit breaker on the supply.	DIY Safe
`N/A`	Sparking inside the microwave cavity	Metal cookware or metal-trimmed dishes are being used, or a metal skewer/foil is touching the inside walls of the oven.	Check you're not using any metal containers or metal-trimmed dishes, and that no metal skewer or foil is touching the oven's interior walls. Contact the service station if it keeps happening.	DIY Check / Tech Fallback

Frequently Asked Questions

Q: I ran the microwave empty by mistake - has this damaged it?

A short spell running empty won't cause any damage, though it's still best avoided.

Q: Can I cook with the roller guide or glass tray removed?

No - the roller guide and the glass tray must both be fitted before you start cooking.

Q: Am I able to open the door while the oven's running?

Yes - you can open it at any point during cooking. The microwave energy cuts off immediately, and the remaining cooking time is held until you shut the door again.

Q: Why does my microwave have moisture inside it after I've cooked something?

That's completely normal - it's just steam from the food condensing where it meets the cooler interior surface of the oven.

Bailey

Smoke & Carbon Monoxide Alarms (2012 Model Year, Orion)

Smoke / CO Alarm

0110 FAQs

View official manual on manufacturer's site ↗

Master Troubleshooting & Diagnostics Matrix

Error Code / Indicator	Symptom / Meaning	Possible Cause	Step-by-Step DIY Fix	Suggested Actions
`N/A`	Holding the test button down for a minimum of 2 seconds produces no alarm at all.	Defective battery or other failure.	Replace the battery or return the unit for service.	DIY Check / Tech Fallback
`N/A`	The alarm's sound is faint or comes out irregular/garbled.	Defective alarm.	Return the alarm for service.	Professional Intervention Required

Thetford

Cassette Toilet C-250/C-254/C-260/C262 CWE

Toilet

2000 FAQs

View full Thetford page →

Reference

Preparing the waste holding tank (from the source handbook). This page is entirely pictogram-based in the source document, with no accompanying text - transcribed here: 1) Open the service door. 2) Release the catch and pull the tank out through the service door. 3) Slide the tank fully out. 4) Lift the tank by the pull handle, tilting it up. 5) Turn/lift open the fill spout cap. 6) Add one measuring cap (150ml) of Thetford Aqua Kem Blue toilet fluid via the fill spout. 7) Add approximately 3 litres of clean water via the same opening. 8) Refit and turn the cap to close it. 9) Rotate the tank back down to its normal position. 10) Press down the automatic pressure-release vent button on top of the tank. 11) Lift the tank by the handle and align it with the service door opening. 12) Slide the tank back into the housing and close the service door.

Emptying the waste holding tank (from the source handbook). This page is entirely pictogram-based in the source document, with no accompanying text - transcribed here: 1) Release the tank from its housing and pull it out through the service door using the pull handle. 2) Press the pressure-release vent button on top of the tank before carrying it. 3) Extend the pull handle upwards. 4) Wheel the tank to a suitable disposal point using its wheels and extended handle. 5) Open the cover over the pour-out spout. 6) Remove the cap from the pour-out spout by turning it. 7) Empty the tank through the spout, pressing the pressure-release vent button to help the contents flow evenly. 8) Rinse the empty tank with approximately 5 litres of clean water through the pour-out spout. 9) Refit and turn the cap to close the pour-out spout. 10) Wheel the tank back to the caravan. 11) Lift the tank by the handle, ready to reinsert it. 12) Reinsert the tank into the housing through the service door, pressing the pressure-release vent button as it is pushed home.

Master Troubleshooting & Diagnostics Matrix

Error Code / Indicator	Symptom / Meaning	Possible Cause	Step-by-Step DIY Fix	Suggested Actions
`N/A`	Blockage when sliding the Waste Holding Tank back into place	The blade handle is not in the correct (closed) position.	Always check that the blade handle is in the correct (closed) position. Never use force if the tank cannot be replaced easily, as this may cause serious damage.	DIY Safe
`N/A`	The toilet will not flush	The Waste Holding Tank Level Indicator flashes when the holding tank is not present in the toilet.	Ensure the Waste Holding Tank is correctly inserted and secured with the safety catch.	DIY Safe

Bailey

Digital TV Antenna System (2012 Model Year, Orion)

TV / Aerial / Satellite

3100 FAQs

View official manual on manufacturer's site ↗

Master Troubleshooting & Diagnostics Matrix

Error Code / Indicator	Symptom / Meaning	Possible Cause	Step-by-Step DIY Fix	Suggested Actions
`N/A`	The Power Pack's red LED stays dark	A faulty coaxial plug, wiring that's incorrect, or a damaged coaxial cable on the antenna dome	Take the antenna dome's cable out of the 'ANT-IN' socket. Should the LED light up at that point, go through each coaxial plug to confirm correct wiring, and look over the coaxial cable itself for sharp bends, kinks, hot surfaces, or proximity to electrical equipment. Our office or an authorised service centre can help further if the LED remains unlit.	DIY Check / Tech Fallback
`N/A`	TV picture quality is poor or affected by interference (Status antenna)	Damage to the coaxial cable (a sharp bend, a kink, or contact with a hot surface), or its route passing near electrical cables, transformers, or similar equipment - any of which can introduce interference, particularly where reception is already weak.	Inspect the coaxial cable routing and ensure it is not damaged or routed near electrical equipment. Remove any excess cable rather than coiling it, as coiled cable can also cause picture distortion.	DIY Safe
`N/A`	TV picture is affected by strong signal near a transmitter (Status antenna)	Gain Control Switch is left on 'NML' (normal) despite being near a TV transmitter, where the resulting strong signal can degrade picture quality.	Set the Gain Control Switch to the Low setting when close to TV transmitters.	DIY Safe
`N/A`	Unclear whether a poor TV signal is caused by the antenna system or the caravan's internal TV wiring (Status antenna)	—	Try a Short Hook-up Test: disconnect the coaxial plugs running from the Power Pack's 'TV-FM' sockets to the TV outlet, and instead wire the TV straight into one of those 'TV-FM' sockets using a fly lead. With the antenna dome plugged directly into 'ANT-IN' and the unit switched on, re-tune the TV for the best signal. An improved picture points to wiring problems between the Power Pack and TV outlet, not a fault with the antenna itself.	DIY Safe

Bailey

Water System (2012 Model Year, Orion)

Water System Component

25010 FAQs

View official manual on manufacturer's site ↗

Master Troubleshooting & Diagnostics Matrix

Error Code / Indicator	Symptom / Meaning	Possible Cause	Step-by-Step DIY Fix	Suggested Actions
`N/A`	No water flows from any tap even though the pump is running.	Water source empty	Confirm the water level and top it up if it's low	DIY Safe
`N/A`	No water flows from any tap even though the pump is running.	Pump wired in reverse	Check the pump's wiring, and refer to its own installation manual for further guidance.	DIY Safe
`N/A`	No water flows from any tap even though the pump is running.	Inlet or outlet pipe has come loose from the pump	Check connections	DIY Safe
`N/A`	No water flows from any tap even though the pump is running.	Pump pipes restricted by kinking	Check pipe runs	DIY Safe
`N/A`	No water flows from any tap even though the pump is running.	The pump's inlet or outlet pipe is blocked.	Check, starting inside freshwater tank	DIY Safe
`N/A`	No water flows from any tap even though the pump is running.	An in-line filter or the pump's own filter is blocked.	Replace filter	DIY Safe
Recommended partsAffiliate linksView 2 optionsHide Check which filter you have. Look inside your water carrier: a cylindrical carbon cartridge screwed onto the bottom of the pump hose is the Aqua Smart filter. Look under the sink: a green cylinder fitted along the blue cold-water pipe is the in-line filter. The handbook doesn't say which filter is fitted, so check yours first. The in-line filter is for 12mm pipe - measure yours before ordering. Filter on the hose in your water carrierWhale WF3000 Aqua Smart Carbon Water Filter~£234.7★ (600+ ratings) - screws onto the end of the pump hose in the water carrier View on Amazon → In-line filter on the cold-water pipeWhale Aquasource WF1230 In-line Water Filter (12mm)~£374.7★ (190+ ratings), third-party seller - fits 12mm pipe; low stock when checked View on Amazon →
`N/A`	No water flows from any tap even though the pump is running.	There's an air leak in the pipe feeding into the pump.	Look for bubbles and clip the connection down securely	DIY Safe
`N/A`	Pump does not run	Pump fuse blown	Inspect the wiring connections, then fit a replacement fuse of the right rating	DIY Safe
Recommended partsAffiliate linksView 2 optionsHide Check whether the blown fuse is a standard or a mini blade fuse (mini ones are roughly half the size), then choose the matching kit: The handbook doesn't say which fuse rating or size is fitted - match the rating printed on the blown fuse. If it's a glass or ceramic cartridge fuse rather than a blade, these kits won't fit. Standard blade fusesCar Fuse Kit - 60pc Assorted Blade Fuses (5A-30A) with Storage Case and Fuse Puller~£5.994.5★ (1,500+ ratings), sold by KANGRUI, dispatched by Amazon - includes 15A blade fuses plus a puller and storage case View on Amazon → Mini blade fusesNilight 120pc Mini Blade Fuse Assortment (5A-30A, ATM/APM) with Fuse Puller~£5.244.5★ (2,500+ ratings), sold by Amazon - includes 15A mini blade fuses View on Amazon →
`N/A`	Pump does not run	Battery disconnected	Check connections	DIY Safe
`N/A`	The cold tap runs normally, but the hot tap's flow is weaker.	Blockage in hot pipeline	Disconnect pipes and inspect	DIY Safe
`N/A`	The cold tap runs normally, but the hot tap's flow is weaker.	A kink in the heater's inlet or outlet pipe is blocking flow	Reposition the pipe run if needed, and confirm the hose fitted is the type Carver recommends	DIY Safe
`N/A`	The cold tap runs normally, but the hot tap's flow is weaker.	Hot tap failed or blocked	Disconnect and inspect	DIY Safe
`N/A`	The cold tap runs normally, but the hot tap's flow is weaker.	Heater non-return valve jammed	Seek service attention from an authorised service centre or specialist	Professional Intervention Required
`N/A`	Water flows from the hot tap but the cold tap's flow is reduced.	A kink in the cold water pipe is blocking the flow	Check and re-route if necessary	DIY Safe
`N/A`	Water flows from the hot tap but the cold tap's flow is reduced.	Blockage in cold pipe line	Take the pipework apart from the first Y-connector onward, checking right through to the tap	DIY Safe
`N/A`	Water flows from the hot tap but the cold tap's flow is reduced.	Cold tap failed or blocked	Disconnect and inspect	DIY Safe
`N/A`	Water flows from the hot tap but the cold tap's flow is reduced.	A fitted Carver Crystal water service unit's cartridge has run out	Replace cartridge	DIY Safe
Recommended partsAffiliate linksView 2 optionsHide Check which filter housing is fitted (and compare it with your current cartridge) before choosing a replacement: The handbook only says a Carver Crystal unit is fitted. The Filtapac cartridge suits Carver/Truma Crystal housings; the Truma Ultraflow filter suits Ultraflow housings and some older Crystal II housings. Match it to the housing you actually have. Carver/Truma Crystal housingFiltapac Water Filter Cartridge & Seal for Truma/Carver Crystal~£12.964.6★ (380+ ratings), sold by Purely Outdoors (third-party seller) View on Amazon → Truma Ultraflow housingTruma Ultraflow Replacement Water Filter (46020-01)~£15.254.7★ (490+ ratings), genuine Truma part, sold by Xtremeauto UK - low stock when checked View on Amazon →
`N/A`	Both the hot and cold taps have reduced flow.	A low battery is making the pump run more slowly than normal.	Check how charged the battery is - see the electrical supply guidance	DIY Safe
`N/A`	Both the hot and cold taps have reduced flow.	Recently-fitted taps could be narrower than needed and restricting flow	Take them off and confirm their bore is at least 6.3mm across	DIY Safe
`N/A`	Both the hot and cold taps have reduced flow.	The pump's filter, or an in-line filter if one is fitted, is partly clogged	Replace filter	DIY Safe
Recommended partsAffiliate linksView 2 optionsHide Check which filter you have. Look inside your water carrier: a cylindrical carbon cartridge screwed onto the bottom of the pump hose is the Aqua Smart filter. Look under the sink: a green cylinder fitted along the blue cold-water pipe is the in-line filter. The handbook doesn't say which filter is fitted, so check yours first. The in-line filter is for 12mm pipe - measure yours before ordering. Filter on the hose in your water carrierWhale WF3000 Aqua Smart Carbon Water Filter~£234.7★ (600+ ratings) - screws onto the end of the pump hose in the water carrier View on Amazon → In-line filter on the cold-water pipeWhale Aquasource WF1230 In-line Water Filter (12mm)~£374.7★ (190+ ratings), third-party seller - fits 12mm pipe; low stock when checked View on Amazon →
`N/A`	Both the hot and cold taps have reduced flow.	A kink in the pump's outlet pipe is restricting the flow	Check and re-route if necessary	DIY Safe
`N/A`	Both the hot and cold taps have reduced flow.	Water leak	Check all water connections	DIY Safe
`N/A`	Reduced flow from either taps	Pipe kinking restricting flow	Check and re-route if necessary	DIY Safe
`N/A`	Reduced flow from either taps	Bore size difference in taps	Fit taps that share the same bore size.	DIY Safe
`N/A`	Water heater difficult to drain	Hot taps left shut, so air can't get into the hot system to let the water drain	Open taps	DIY Safe
`N/A`	Water heater difficult to drain	Air bleed pipe is kinked or clogged	Unkink or unblock pipe	DIY Safe