Dometic • Sine Wave Inverter

Dometic WAECO SinePower

Official technical documentation and workshop diagnostics for Dometic WAECO SinePower.

Technical Specifications

ElectricalInput: 12 V DC (10.5 V - 15 V) or 24 V DC (21 V - 30 V). Output: 230 V AC pure sine wave at 50/60 Hz. Continuous Output Power: 700W (MSP 702/704), 1000W (MSP 1012/1024), 1500W (MSP 1512/1524), 2000W (MSP 2012/2024), 2500W (MSP 2512/2524). Peak Output Power: 1400W to 5000W. Recommended DC Fuse & Cable Cross-Sections: MSP 702: 100A, 25 mm²; MSP 704: 50A, 15 mm²; MSP 1012: 200A, 35 mm²; MSP 1024: 100A, 25 mm²; MSP 1512: 200A, 35 mm²; MSP 1524: 100A, 25 mm²; MSP 2012: 250A, 70 mm²; MSP 2024: 150A, 55 mm²; MSP 2512: 400A, 95 mm²; MSP 2524: 200A, 70 mm².
Gas Or PressureNot applicable
Capacities DimensionsOperating ambient temperature: 0 °C to 40 °C. Storage temperature: -30 °C to +70 °C. Dimensions: 190 x 380 x 90 mm (MSP 7xx), 225 x 435 x 117 mm (MSP 10xx), 225 x 465 x 117 mm (MSP 15xx), 349 x 516 x 116 mm (MSP 20xx), 349 x 546 x 116 mm (MSP 25xx). Weight: 5.5 kg to 16.9 kg.

Master Troubleshooting & Diagnostics Matrix

Error Code / IndicatorSymptom / MeaningPossible CauseStep-by-Step DIY FixSuggested Actions
N/A
LED 'Power Status' flashes rapidly in red (Input Voltage Too High)
Input voltage exceeds permissible limit (> 15.0 V for 12V models, > 30.0 V for 24V models).
Ensure the inverter is connected to the correct nominal voltage system. Verify charging system regulator outputs.
DIY Safe
N/A
LED 'Power Status' flashes slowly in red (Input Voltage Too Low)
Input voltage has dropped below the low-voltage shutdown threshold (Under 10.3 V - 10.6 V for 12V, 20.5 V - 21.2 V for 24V).
Recharge the battery immediately. Check DC supply cables, terminals, and connections for voltage drop.
DIY Safe
N/A
LED 'Power Status' flashes periodically in red (Thermal Overload)
Internal temperature or heat sink temperature has exceeded the safety shutdown limit (internal > 70 °C, heat sink > 90 °C).
Turn off the inverter and load. Allow 5 - 10 minutes to cool, reduce load, clear blocked ventilation paths, and ensure adequate airflow before restarting.
DIY Safe
N/A
LED 'Power Status' stays continuously lit in red (Short Circuit / Overload / Reverse Polarity)
Output short circuit, load exceeds rated capacity, or reverse polarity on DC input.
Turn off the inverter, disconnect the load, and test without load. If error clears, the appliance has a short circuit or draws excessive power. Check cables and connections.
DIY Safe

Frequently Asked Questions

Q: How can I use mains-powered gadgets in my motorhome or caravan?

Everything built into a motorhome or caravan - lights, fridge, heating, water pump - normally runs on 12V DC from the leisure battery, which is fine on the move. To use 230V devices such as a hairdryer, coffee machine or laptop charger away from hook-up, you need an inverter, which turns the battery's 12V DC into 230V AC.

Power demands keep growing, and the standard electrical system a vehicle leaves the factory with can quickly reach its limits, so think about how you tour: whether you'll run 230V devices on board, whether batteries need recharging quickly on mains, and how often you drive between stops (which lets the batteries recharge).

A well-planned energy management system should then always have enough power available. Dometic's inverters take 12V or 24V from the battery and supply 230V AC through an ordinary household-style socket - but not every inverter can run every appliance, so choose one that suits the devices you'll use.

Q: My Dometic inverter has failed - where do I get a replacement?

Contact your caravan or motorhome dealer.