← Back to Appliance Troubleshooting
CBE • Power Control Systems

CBE PC210-ST

Official technical documentation and workshop diagnostics for PC210-ST.

Reference

25.5° 1 2 3 4 5 6
Control panel button legend, page 15 of the CBE PC210-ST manual. This diagram's own numbering restarts at 1 - it is separate from the LCD visualisations diagram below, whose numbering also restarts at 1.
  1. 1 On/off main button (to turn on/off press for 2 seconds): at the start-up the display carries out a functioning test and shows all symbols (including unused symbols).
  2. 2 Button to check the car battery (B1) and the leisure battery (B2) and for the regulation of the programmable parameters' setting (see USER'S SETTING).
  3. 3 Button for the control of fresh water tank (in %), for fresh water refilling function operation (see "FRESH WATER TANK REFILLING" function) and for the regulation of the programmable parameters' setting (see USER'S SETTING).
  4. 4 Button to switch the lights and the heating/boiler on and off.
  5. 5 Button to switch the pump on and off.
  6. 6 Function A) Button to switch the awning light on and off (only after button ref. 4 has been activated). Function B) Button to enter the set mode (see USER'S SETTING). NB: the temperature sensors are optional.
88.8 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
LCD status-icon legend, page 16 of the CBE PC210-ST manual - a separate diagram from the button legend above, with its own 1-16 numbering. "Symbol ref. N" in the fault table below refers to this diagram.
  1. 1 "B2" leisure battery status display.
  2. 2 Fresh water tank status display.
  3. 3 It shows the car battery (B1) test, the blinking indicates the discharged battery alarm.
  4. 4 It shows the leisure battery (B2) test, the blinking indicates the discharged battery alarm.
  5. 5 External temperature digital indicator.
  6. 6 Internal temperature digital indicator.
  7. 7 It displays the set mode.
  8. 8 It displays the temperatures and the required test.
  9. 9 It shows the unit of measure.
  10. 10 It shows the fresh water tank test, the blinking indicates the empty tank alarm.
  11. 11 It displays that the waste water tank is full.
  12. 12 It shows that the minimal voltage device has switched on.
  13. 13 It displays the batteries' paralleling when engine is on.
  14. 14 It indicates that the engine is on.
  15. 15 It displays that the 230V net is connected.
  16. 16 It displays that the car battery recharging unit is on.

Master Troubleshooting & Diagnostics Matrix

Error Code / IndicatorSymptom / MeaningPossible CauseStep-by-Step DIY FixSuggested Actions
Symbol 3 blinking
Car battery alarm (B1)
When the battery reaches a voltage lower than 12V
This alarm clears itself once the voltage climbs back over 12.5V.
DIY Safe
Symbol 4 blinking and two short beeps
Leisure battery discharge alarm (B2)
When leisure battery voltage gets 10.5V
This alarm also clears itself once the voltage climbs back over 12.5V.
DIY Safe
Symbol 12
Minimum voltage control (battery protection) / electronic battery protection cuts off 12V users
The leisure battery has reached 10V (or the control panel has turned itself off entirely below 9.5V)
Pressing the on/off button on the control panel gives everything one more minute of power, and it all reconnects automatically once the voltage climbs back above 13.5V.
DIY Safe
Symbol 10 blinking
Fresh water tank alarm
Alarm turns on when fresh water level is lower than 10% of the tank capacity
The alarm clears itself automatically once the level rises back above 20%.
DIY Safe
Symbol 11 blinking
Waste water tank alarm
The waste water tank has reached its screw-probe sensor level
The alarm is shown acoustically (when the engine is off) and visually via symbol ref. 11 blinking.
DIY Safe